Company Logo

• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC is an excellent option for modern homes. They are easy to maintain and durable, as well as long-lasting. They do not get rotten or rusty like aluminum and timber.

It is essential to clean and oil UPVC doors and windows on a regular basis. This will reduce costly repairs and increase energy efficiency.

1. Broken Glass

The broken glass in your windows can cause significant damage to your home, and could even be fatal. You should take the time to ensure that your windows are in good condition.

Single-pane windows are fairly simple to replace, and they typically fit into frames of the past easily. However If windows with double glazing repairs panes are anchored by internal beading, it will be more difficult to remove the old panes and put in new ones. In this situation, you will need to source some plastic spacers that help the new pane to fit properly into the window frame.

Wearing eye protection and heavy gloves is a must when you are planning to remove the glass by yourself. You should also lay down a dropcloth before you begin working on the window panes to ensure that any shards fall onto the fabric and not on the floor which could cause them to be trampled under.

After the glass has been removed and the glass is removed, it's a good idea to cover the gap with packaging tape or duct tape to prevent drafts and water from entering the property until a professional is able to come out and fix the window. It also acts as an obstacle to stop intruders from getting into your home. If the gap is large, you might be interested in the security door with an integrated window, since it offers the best of both worlds.

2. Sagging

Upvc windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber sash windows. However, with time, they are susceptible to a range of problems including sagging. A sagging uPVC window can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to sag it's important to act quickly to prevent the problem from worsening.

To repair a window that is sagging, you can try to reposition the hinges. First, you'll need to open the windows to get at the frame. You can then unscrew both the hinges at the top and bottom using a screwdriver and adjust them counter-clockwise or clockwise. Once you've repositioned the hinges, close your window and test it for an appropriate fit. If you are happy with the size of the window, you can tighten screws to keep them in place.

If you aren't able to move the hinges you may need to replace the seal. Rubber seals may dry out and lose their elasticity with time, which causes them to loosen. It is important to replace your seal as soon as you can in order to keep your uPVC window waterproof and draughtproof.

UPVC handles can also become loose. Often this is due to screws that have become loose over time. However, it could also happen because the handle mechanism has worn out. Luckily, it's not difficult to fix the loose uPVC window handle yourself. First, you'll need close your window and do a test to ensure that it fits. The corner joints of the sash need to be aligned with the casing joint. If it doesn't then you can use a screwdriver to loosen the handle, and then reverse the mechanism back into position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains it is important that you take action. The leaks of water from windows do are not just a cause for degrading of the structure of your home but also hamper your efforts to control the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is an easy fix that can be accomplished by any DIYer who is competent. Depending on the severity of the issue is, old caulking may have to be removed. It is crucial to remember that when it is about uPVC window repairs, window repairs do not be tempted to apply too much caulk in order to make the area more difficult to clean and could reduce your energy efficiency.

Verify that the drainage holes have no debris inside them and ensure that the sill pan has been properly angled to drain away from the window. In more serious cases you might need to consider replacing the window.

Mold spots and rotten sills are also signs of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the house.

It is also important to keep in mind that if the leak is coming from between the glass of your double glazing near me-glazed windows it may be more likely to be an issue with the glass seal, rather than the frame or sliding. Again this can easily be fixed by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and open in a breeze It could be hinges that are at the fault. They can be easily replaced by any competent DIYer and can be completed in a matter of minutes.

Most households in the UK will have either top hung or side-hung uPVC windows that are hinged and, like all mechanical parts, they are susceptible to wear and tear over time. It is very easy to change the hinges on a window however it is easier if someone helps you to hold the frame.

Check that the uPVC hinges are open and closed in the correct direction. This can be done by looking for the arrow on each hinge. This indicates which way the window should open.

Window hinges that aren't working properly could be the result of incorrectly opening the window in a particular way or due to poor installation at the factory. Sending us a picture via our website is often enough to solve the issue. We are more than happy to offer assistance.

Regularly lubricating hinges is also essential. Applying a light engineering lubricant on the hinges is a good way to do this. We suggest using an oil that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window to operate and close more easily. It also helps prevent corrosion and reduce the possibility of sticking. This must be done at a minimum once a year. WD40 and other solvent based lubricants are not recommended as they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different causes. First, the hinges due to wear and tear can become misaligned, this can cause gaps to develop between the sash and the frame. These can be easily repaired by giving them a thorough clean, however when they're beyond repair, it may be necessary to have them realigned or replaced. In addition, the interlock could be misaligned. This happens on the hinge side and might require to be cleaned. In certain instances it is possible to replace them.

The next common reason for draughts is window seals, these are susceptible to being worn out or damaged over time and let air escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the window with glass that is low-emissivity, which will help regulate indoor temperatures and again will reduce the risk of draughts.

Another method of reducing the amount of draughts is to use a draught-excluder. These are usually made of fabric tubes filled with a filler which can be hung over your window sill. These will help to block out cold air and keep your home warm and cozy!

Your upvc windows can keep providing excellent insulation and security for your home with regular maintenance and repairs. It is crucial to keep in mind that all windows eventually wear out and it could be more cost-effective to replace them rather than repair them. So, if you are experiencing issues with your Upvc windows, it's recommended to seek help from a professional immediately.