Company Logo

• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window is an inconvenience. It could also be a chance to upgrade your glass to energy-efficient or insulated windows, and enjoy benefits such as greater comfort, a higher resale value and reduced utility costs.

This is a project you could take on yourself for only a fraction of the cost of hiring a professional. You only need the appropriate tools and a few minutes of your time.

Glass

Replace your single-paned windows with tempered insulate glass to improve energy efficiency, reduce noise, and preserve the historical integrity of your home's older. The majority of homeowners with basic hand tools can repair windows with ease. In addition to a new pane, the following items are required such as latex glazing putty; glazier's points; pliers; and an electric heater to warm the old putty, replace window pane if needed. Before beginning, wear gloves and safety glasses as working with broken glass may cause injuries.

Begin by removing any broken pieces of glass. It is recommended to use pliers, but a flathead can be useful as well. Make use of a wood chisel or putty knives, to take away any old putty remaining around the frame and the window sash. Be careful and slow, taking care not to damage the old window sash. This should be done on a ladder, not the ground. Also, you should have someone on the ground to ensure it is held steady.

Once you have removed all of the old putty, prepare the window frame to accommodate the new pane. To allow for seasonal expansion or contraction, subtract 1/8 inch each from the measurements of the width and height. These measurements can be taken to a hardware or home center store to have a piece cut of stock glass to the right size. You can also cut the glass by yourself if you have the right tools.

After installing the glass After installing the glass, apply some caulking to the edge. This will make the glass weatherproof. Install a glazier’s point on both sides of the frame. This will secure the pane. The points shouldn't be so tight that they cause friction between the sash and the frame however they should not be too loose.

Before putting the putty on, make sure to knead it until it's soft and free of lumps. Then you can roll it into pencil-sized strips. Apply the first strip to the frame's corner. Work from one corner to the next, making sure it is even and smooth.

Glazier's Points

The glazier's points are tiny triangular metal pieces that allow glass to be secured into the window frame without damaging the delicate surface. Knowing how to use these hidden tiny pieces of help is simple and could save you money on a professional installation or the cost of purchasing new glass.

After the old putty and the glazier's points have been removed, thoroughly clean the frame using a utility knife to remove any remaining residue. If needed it is necessary to lightly sand the wood along the grooves of the rabbets to smooth rough areas. If you do sand the wood, ensure you protect it with painter's tape to avoid accidental damage.

Take measurements of the empty frame and record precise measurements. Take these dimensions to a hardware store or a home center and have the new pane cut slightly smaller than the frame's opening. This will ensure a secure fit, and allow for expansion and contraction.

Place the new pane in the frame and press it down with your hands. Utilize the point of the chisel or the back of the putty blade to smudge the glazier's points as illustrated in Figure 11. The glazier's point should be flush against the top edge of your pane and the shoulders should be just beneath that lip.

Apply a thin layer glazing compound to the rabbet grooves and the edges of the glass. This will protect and seal the edges. Let it dry and cure completely.

Install the new window sash after the glazing compound has dried. The first step is to coat the wood with a thick coat of Linseed oil. This will prevent the new putty from soaking up moisture and drying out and cracking with time. Use a brush to apply this coat, or the point of the putty blade. Then, use the chisel that is on the back of the putty tool or the back of the putty handle to gently hammer the new sash or glazier's point into rabbet grooves. Repeat this process in intervals of 10 inches around the frame.

Putty

A baseball that is thrown or a rock that is errant or a falling branch can cause a window pane to crack or break. Most windows can be repaired easily by putting in a new piece. The glass window replacement is held in position by a small metal clip, called a glazier's point and putty. This compound is also called glazing compound. Remove the old pane and clean the area using a rag, a pull-type scraper or wood chisel. Wear gloves and safety glasses while working. If the window is secured to the frame, you'll have to make use of a heat gun to soften the adhesive before cutting it loose.

If you are planning to Replace Window Pane the original sash in the future, take care to remove any molding pieces that secure the old pane. Then, sand the sash to make sure it's flat and ready for new caulk. Once the sash is re-installed, apply a new silicone caulk to the glass to ensure that it doesn't swell or fade over time.

Remove the glazing points in the rabbets. These are the grooves on the sash, where the glass is. If they're difficult to work out, try placing an instrument like a heat gun to soften them before you do. When using a heating tool, be sure to not damage the sash and its railings.

After the old glazing points and putty have been removed prepare a bed for the new pane. Roll a rope of glazing compound between your fingers and make it around 1/2 inch thick. Place it into the rabbets where the glass will be put. The glass should rest against the putty on both sides. If needed gently tap your glass into the rabbet with your thumb.

If the new pane has a crack, you can cover it with a solvent-based glue or silicone caulk prior pressing it into the sash. If the crack isn't sealed, you will need to use putty to keep water from getting in. When the putty dries, clean the oily film off the glass using the help of a rag. Allow it to completely dry before painting. Paint after the putty has dried completely. It won't form a good seal and could discolor or leak over time.

Paint

You might be worried about replacing a broken piece of glass. It's true that replacing a single pane of glass doesn't need to be costly when you do it on your own. Even double-paned windows can be replaced for a fraction of the price it will cost an expert.

If you are working with a large glass window first, ensure that it is securely attached to the frame. Using the proper tools and techniques to make this task relatively easy and replace window Pane speedy.

When you're ready to start with the removal of the old window by prying out the glazing points made of metal that are attached to it. These are tiny triangles of metal that act as "nails", holding the window in place. They are submerged under a bead of glazing putty, which transforms into a solid moulded wedge that secures the window in place and hides the edges.

After you have the old pane removed Clean up the frame and wood. Scrape away any paint and sand down the rabbet grooves, where the glazing points were. Sand them down to clean wood surfaces, so that you can paint the frames with the same color. After sanding the wood then apply a layer of flax oil. This will help to prolong the life of the frame.

The next step is to measure the dimensions of the window's opening. You'll need to take vertical and horizontal measurements of the entire opening, as well as the thickness of the old pane. To determine the exact dimensions of the new pane, subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. Take these dimensions to a hardware or home improvement store, and they will have cut the glass for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.