Company Logo

• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

Double Glazing Door Lock Repairs

Has your uPVC window or door mechanism deteriorated? Perhaps the door or window handles aren't able to connect properly or are hard to use.

It is essential that the double glazed doors function smoothly, or else you'll lose energy and increase the chance of burglary. Owen the Locksmith will be able to fix your door lock at an affordable price.

Snapped Key

It can be a hassle when a key gets stuck inside the lock. It could also be a security risk, as the door may not lock and make you vulnerable to intruders. There are fortunately quick fixes you can try to resolve the problem and get your door functioning properly once more.

First, remember to stay calm. If you panic and begin poking around wildly you could end up pushing the broken piece of the key further into the lock, making the situation worse.

Spray WD-40, repaired or any other penetrating oil, into the lock. This will help the broken piece be removed more easily. You can also make use of a screwdriver to break pieces that could be hindering the flow. If you have a piece of the key that is stuck, grab it with the help of a paperclip or any other thin metal object and pull it. Both methods work well, however, be very careful not to push the broken piece of the key even further into the keyway.

Some paperclips come with grooved edges which can be used as hook extractors. Jigsaw blades are also well for this. If you don't happen to have any of these, you can bend a hook using needle-nosed pliers. Additionally, a pair of tweezers can be used to grip and remove the remaining bit of the broken key.

If you cannot remove the broken key piece then you can use a lock deicer. It is available in most hardware stores and is used to freeze any moisture that may be present within the lock.

If none of these solutions work, it could be time to call a locksmith. The experts at Fitlocks can quickly fix problems such as broken handles and snapped keys using uPVC locks and door mechanisms. They can also alter your double glazing door mechanisms to make them more user-friendly. Request a repair for your double glazing via our website or give us a phone call to discuss your requirements.

Broken Cylinder

A damaged cylinder poses an immediate security risk. It's a good thing that it's a simple repair for an expert locksmith to complete. To fix the cylinder, locksmiths must tap it. This can be accomplished with the hammer or other tool. However, the best method is to make use of a wire or a long match. Then, place the match's end or wire near the keyway. The locksmith will hit the lock to break it open. This is superior to using a hammer, which can cause damage to the lock.

The most frequent cause for cracks in the head of a cylinder is due to overheating. This can happen when the block and the cylinder head are made from different metals such as cast-iron and aluminium. When the different metals heat up and cool down at different rates, it may create hotspots locally that expand faster than the rest of the head of the cylinder, leading to cracks.

Another possible cause of cracks in the cylinder is corrosion. If the cylinder head and the block of the cylinder are not properly maintained, it can cause corrosion or rust and cause them to expand at more than they should. This can lead to cracks as time passes.

If your uPVC window or door lock is stiff and requires a lot more pressure to turn, it could be due to a variety of causes. A malfunctioning locking mechanism, misalignment or the wear of the handle are typical causes of this issue.

This is a simple and inexpensive fix that most double glazing owners can accomplish. A professional locksmith is able to solve this issue within an hour of arriving at the property. They can repair the locking mechanisms, or change the window handles, and also change the gearboxes, based on your particular requirements. A professional locksmith will always be able to advise you on the most cost-effective options for your home. They may suggest upgrading to 3 Star TS007 Euro Cylinders, which offer an additional layer of protection against burglars. This is a small cost to pay for the security that comes with knowing your uPVC doors are safe.

Broken Handle

It's not surprising that window handle locks could break. They have complex mechanisms which deteriorate over time. If yours fails, it can be difficult to determine the source of the issue. Make sure you fix it properly.

Fixing the broken handle, regardless of whether it's the internal locking mechanism or latch will increase the security of your uPVC door and stop draughts. It is costly to repair or replace your handle if it is not done correctly and can also harm the frame and the lock of your door.

Screwdriver: With the window open and the screw loose, loosen the handle. The screw should be on the inside face of the back plate, normally covered by an attractive cover for the screw for aesthetic reasons. It is important to not be able to replace any internal parts of the handle such as the plates and levers on either side. Ideally, keep them in the same order so you can replace them if needed.

Next, turn the handle until it's 90 degrees towards the window frame. Then, loosen the screw on the back of the handle that holds it to the internal spindle with another screwdriver. Once the screw is loose, you should be capable of pulling the handle off and pull out the broken spindle. Replace it with a new one, ensuring it's the same length as the old one (you can usually find these on the internet or at hardware stores) and securely screw it in place. Do not tighten the screw too much because this could cause damage to the handle and window frame.

Check that the new handle is fitted after which you can close and test the handle. It should function smoothly and you'll be able to open your windows after a few times.

Make sure to check that your uPVC window is shut correctly when you're using the handle. If they're not closing properly cause damp and draughts in your home as and also affecting your home's energy efficiency. A local window company, like Core Sash Windows, will be capable of adjusting the hinges on your window frames so they are able to shut properly.

Broken Spindle

It is more typical for the spindle to break than the handle. This is especially frequent in uPVC tilt and turn windows. These windows require a handle that acts as a locking device in the frame of the window. The handle is attached to a centre rod that is then activated by a series of mushroom-like locking cams, these secure the frame of the window. If the dead latch mechanism is not able to open when the handle is turned it is likely that the spindle is broken, this can be a frustrating problem.

There are solutions to this issue. A good locksmith can quickly and efficiently solve the issue. They can take apart the window handle using a tool that removes the wheel part of the mechanism that is where the spindle goes. This is done without causing any damage to the handle or causing any other damage to the frame of the window replacement.

Once the wheel has been removed the technician can then inspect the spindle and determine what has caused it to break. This involves breaking down the spindle into its component parts and meticulously noting their general condition, as well as any specific areas of damage or excessive wear. This process is usually performed by technicians in a clean and safe environment.

The next step is to clean the damaged spindle. This assists in removing any dirt or debris that could be hindering its normal functioning. After this, the spindle could be repaired or replaced. If it's being replaced, the technician could use an identical dowel size to the original and drill mating holes in both pieces of the spindle. This will ensure that the spindle will fit perfectly with the handle.

If the damaged spindle cannot be repaired, it might need to be replaced entirely. Home centers can sell generic replacements however if your window design is unique, you will require contacting an expert in cabinet making or repaired woodworking who can replicate the exact component. Once the spindle has been installed, it can be fixed to the handle. The screw holes on the handle with the screws already in the frame. Once the handle is set, you are able to operate your uPVC windows.